LPC2377/78 Single-chip 16-bit/32-bit microcontrollers; 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC
General description
The LPC2377/78 microcontrollers are based on a 16-bit/32-bit ARM7TDMI-S CPU with real-time emulation that combines the microcontroller with 512 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical performance in interrupt service routines and DSP algorithms, this increases performance up to 30 % over Thumb mode. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 % with minimal performance penalty.
The LPC2377/78 are ideal for multi-purpose serial communication applications. It incorporates a 10/100 Ethernet Media Access Controller (MAC), USB full speed device with 4 kB of endpoint RAM (LPC2378 only), four UARTs, two CAN channels (LPC2378 only), an SPI interface, two Synchronous Serial Ports (SSP), three I2C-bus interfaces, an I2S-bus interface, and an External Memory Controller (EMC). This blend of serial communications interfaces combined with an on-chip 4 MHz internal oscillator, SRAM of 32 kB, 16 kB SRAM for Ethernet, 8 kB SRAM for USB and general purpose use, together with 2 kB battery powered SRAM make this device suited for communication gateways and protocol converters. Various 32-bit timers, an improved 10-bit ADC, 10-bit DAC, PWM unit, a CAN control unit, and up to 104 fast GPIO lines with up to 50 edge and up to four level sensitive external interrupt pins make these microcontrollers suitable for industrial control and medical systems.
Features and benefits
• ARM7TDMI-S processor, running at up to 72 MHz.
• Up to 512 kB on-chip flash program memory with In-System Programming (ISP) and In-Application Programming (IAP) capabilities. Flash program memory is on the ARM local bus for high performance CPU access.
• 32 kB of SRAM on the ARM local bus for high performance CPU access.
• 16 kB SRAM for Ethernet interface. Can also be used as general purpose SRAM.
• 8 kB SRAM for general purpose DMA use; also accessible by the USB.
• Dual Advanced High-performance Bus (AHB) system that provides for simultaneous Ethernet DMA, USB DMA, and program execution from on-chip flash with no contention between those functions. A bus bridge allows the Ethernet DMA to access the other AHB subsystem.
• EMC provides support for static devices such as flash and SRAM as well as off-chip memory mapped peripherals.
• Advanced Vectored Interrupt Controller (VIC), supporting up to 32 vectored interrupts.
• General Purpose DMA controller (GPDMA) on AHB that can be used with the SSP serial interfaces, the I2S port, and the Secure Digital/MultiMediaCard (SD/MMC) card port, as well as for memory-to-memory transfers.
• Serial Interfaces:
-- Ethernet MAC with associated DMA controller. These functions reside on an independent AHB.
-- USB 2.0 full-speed device with on-chip PHY and associated DMA controller (LPC2378 only).
-- Four UARTs with fractional baud rate generation, one with modem control I/O, one with IrDA support, all with FIFO.
-- CAN controller with two channels (LPC2378 only).
-- SPI controller.
-- Two SSP controllers with FIFO and multi-protocol capabilities. One is an alternate for the SPI port, sharing its interrupt and pins. These controllers can be used with the GPDMA controller.
-- Three I2C-bus interfaces (one with open-drain and two with standard port pins).
-- I2S (Inter-IC Sound) interface for digital audio input or output. It can be used with the GPDMA.
• Other peripherals:
-- SD/MMC memory card interface.
-- 104 General purpose I/O pins with configurable pull-up/down resistors.
-- 10-bit ADC with input multiplexing among 8 pins.
-- 10-bit DAC.
-- Four general purpose timers/counters with 8 capture inputs and 10 compare outputs. Each timer block has an external count input.
-- One PWM/timer block with support for three-phase motor control. The PWM has two external count inputs.
-- Real-Time Clock (RTC) with separate power pin, clock source can be the RTC oscillator or the APB clock.
-- 2 kB SRAM powered from the RTC power pin, allowing data to be stored when the rest of the chip is powered off.
-- WatchDog Timer (WDT). The WDT can be clocked from the internal RC oscillator, the RTC oscillator, or the APB clock.
• Standard ARM test/debug interface for compatibility with existing tools.
• Emulation trace module supports real-time trace.
• Single 3.3 V power supply (3.0 V to 3.6 V).
• Four reduced power modes: idle, sleep, power-down, and deep power-down.
• Four external interrupt inputs configurable as edge/level sensitive. All pins on Port 0 and Port 2 can be used as edge sensitive interrupt sources.
• Processor wake-up from Power-down mode via any interrupt able to operate during Power-down mode (includes external interrupts, RTC interrupt, USB activity, Ethernet
wake-up interrupt).
• Two independent power domains allow fine-tuning of power consumption based on needed features.
• Each peripheral has its own clock divider for further power saving.
• Brownout detect with separate thresholds for interrupt and forced reset.
• On-chip power-on reset.
• On-chip crystal oscillator with an operating range of 1 MHz to 25 MHz.
• 4 MHz internal RC oscillator trimmed to 1 % accuracy that can optionally be used as the system clock. When used as the CPU clock, does not allow CAN and USB to run.
• On-chip PLL allows CPU operation up to the maximum CPU rate without the need for a high frequency crystal. Can be run from the main oscillator, the internal RC oscillator, or the RTC oscillator.
• Boundary scan for simplified board testing.
• Versatile pin function selections allow more possibilities for using on-chip peripheral functions.
Applications
• Industrial control
• Medical systems
• Protocol converter
• Communications
Notice:
1. As a Diamond Member and an Audited Supplier of Made-in-China since 2014, Telefly guarantees that all the semiconductor chips and other electronic components we provide are 100% new and original, all the chips and components are from formal channels and can be traced back to original manufacturers.
2. All products we provide will be double checked and proper inspection process will be strictly followed before delivery.
3. We promise to provide at least 1 year after-sell service for all products we sell.
4. Due to the reality of sometime volatile changes of the chips and components' stock and prices, please contact with us for their availability and quoting prices before payment.
5. We use DHL, UPS, FedEx, TNT, HONGKONG Post, EUB, EMS or other global express delivery services you designate.
Company Profile
Company Profile
TELEFLY Telecommunications Equipment Co., Ltd. is a leading Chinese Telecommunications Equipment manufacturer and a semiconductor chip and other electronic component distributor founded in 2004, certified by SGS, CFL Certification Center. We provide high quality and price competitive semiconductor chips and other electronic components, Ethernet switch ,SFP transceiver,media converter ,patch cable, Fiber Optic Splitter and so on. Up till now, our products and solutions have been deployed in over 60 countries and regions, TELEFLY is looking forward to strengthening friendly cooperative relationships with all clients, creating benefits together and sharing the joy of success!
Our Advantages
Why you choose TELEFLY be one of your partner?
1.Customer get satisfied quality and service with competitive price and punctual delivery.
2.OEM service with 13-year experiences, free samples are available.
3.Prompt answer for any question and inquiry in the shortest time.
4.Factory directly,reduce your cost and save time.
1.Customer get satisfied quality and service with competitive price and punctual delivery.
2.OEM service with 13-year experiences, free samples are available.
3.Prompt answer for any question and inquiry in the shortest time.
4.Factory directly,reduce your cost and save time.
FAQ
Q1 . What your MOQ?
A1 .If not specified, 1 pcs is ok,whatever how many you need,and we will also give you the best service.
Q2.What certification did you get?
A2 : Our product strictly operate the ISO9001:2008 quality control system and we passed the CE,FCC,ROHS and SGS test,you can trust us.
Q3 :What about your package and delivery,will it broke during shipping?
A3:You don't need to worry about the package,we will use shockproof case for delivering.
Q4.What your common delivery way?
A4:By air, by sea or express(UPS,DHL,Fedex,TNT,EMS...)We will make a perfect delivery plan for you.
Q5.Tell me some detail about warrant time.
A5:We give you the promise if any question during 1 year and not cause by human factors,we will fix it.
Audited Supplier 
){kind=link}
){kind=link}